How Do I Make My Ge Profile Washer Go Into Service Mode

GE Front end Load Washer Service manner

GE front load washer repair tin be tricky; however, this folio is hither to help. The way these washers are designed information technology is almost impossible to diagnose them without placing them in the service mode. In the service mode you have total control over the washer and then that you can test components such as the motor, pump, inverter, water valve and others. Likewise while in the service mode, you tin view error codes that are sometimes vital to accurately diagnose problems with these washers. This page will explain how to use the service mode to assist with GE front load washer troubleshooting.

Entering And Exiting The Service Manner

Follow these steps to enter the service mode on a GE front load washer.

1. Close the door.

2. Articulate electric current cycles by pressing the ability button. Make sure the screen is blank before attempting to enter the service mode.

three. Disconnect ability to washer for at to the lowest degree 30 seconds.

4. Reconnect the power and within xxx seconds of reconnecting power complete the adjacent step.

5. Press signal -delay first -signal - delay offset.

Note: Entering the service mode is a lilliputian different on models GFWN1000, GFAN1000,GFWN1100, and GFAN1100. To enter the service mode on these models press signal, extra rinse, signal and extra rinse. Press the aforementioned push sequence to exit the service manner.

If you successfully enter the washer into the service, fashion t01 will be displayed and the door will lock.

Never disconnect the power to the washer while it is in the service mode. Doing so may result in a damaged control board.

To exit the service mode press bespeak -delay start -indicate- delay start.

t01

When you lot enter the service mode, t01 is displayed. This test mode has no diagnostic purpose. The primary board is designed to piece of work on multiple models and this style is for setting the model. For the virtually function, you shouldn't accept to worry about this test mode when diagnosing. To enter this test mode, press start/intermission and to go out press power.

t02

Error Codes Test Mode

To enter the error code examination way on a GE front load washer, rotate the control knob until t02 is displayed in the control panel and so press start/pause to enter the exam mode. This is where all error codes are stored. Once y'all take entered the exam mode, yous will encounter the most recent error code that the command has flagged. If you printing start/pause you will run into the adjacent contempo fault code. If you continue to press get-go/interruption you can view up to the ten almost recent error codes. Almost of the time in that location volition be merely ane or two.

Once you have diagnosed the washer information technology is very important to clear the error codes. If you don't clear the error codes, when you lot have another problem the old error codes will still be there from an issue that has been resolved. To clear the error codes press and hold beginning/pause. Printing power to exit this test style and the brandish should go back to t02.

t03

This test mode simply displays software revision numbers. This has no diagnostic purpose.

t04

LED And Buttons Test Fashion

To enter the LED and buttons test style on a GE front load washer, rotate the command knob until t04 is displayed in the control panel then printing starting time/pause to enter the exam mode. This test mode will examination to see if each push works and each LED will light. Each calorie-free should blink one time in a loop. To test the buttons, press each button and if the control senses that the button has been pressed, you volition hear a beep. If you practice not hear the beep, the push is broken and yous will have to supervene upon the main control. Press power to exit this exam mode and the display should go dorsum to t04.

t05

Water Pump Test Mode

To enter the h2o pump examination way, rotate the control knob until t05 is displayed in the command console then press kickoff/pause to enter the exam mode. Once you have entered the exam mode, "P" will exist displayed and the pump will run for sixty seconds. Subsequently threescore seconds it will return to t05. To go out this exam style early, press ability to return to t05.

If the washer will not pump out the first affair you should do is remove the bottom panel to admission the pump clean out and then make clean out the pump.

t06

Water Lever Command Test Mode

To enter the h2o level control test fashion on a GE front end load washer, rotate the control knob until t06 is displayed in the command panel then printing starting time/pause to enter the test mode. This test has five steps as described below.

Once you start the test, the water pump volition brainstorm to run and "Due east" will be displayed in the control console. The "East" beingness displayed means that the tub is empty. If the tub is empty, but "East" is not displayed and so the h2o level command is bad.

Press showtime/pause to advance to the next level of the test. At this point the water will begin to run. When the water level in the tub reaches the cream level, "F" volition be displayed in the control panel and h2o will stop running. Foam water level is virtually ¾ of an inch in the wash handbasket.

Printing start/pause to advance to the next level of the test. Water will offset to run again and when the tub reaches the main level, "nl" will be displayed in the control console and the water will stop running. The main h2o level is about 2 ½ inches of water in the wash basket.

Printing first/break to accelerate to the next level of the examination. H2o will run until overflow water level is reached. Once the overflow level is reached, "oF" will be briefly displayed in the control panel. Overflow is approximately 6 inches above the door opening.

Soon later on the overflow water level is reached, the water pump will energize and pump the water out. Once the tub is empty once more, "E" will be displayed again. Pressing power anytime during the test mode volition exit the test manner.

t07

Water Heater Test Fashion

To enter the water heater test fashion on a GE front load washer, rotate the control knob until t07 is displayed in the control panel then press get-go/pause to enter the test fashion. Once this test is entered, the washer will start to make full with water until the master water level is reached. Once the washer is filled to the main water level, the heater will come on and commencement to oestrus the water for 5 minutes. During this time, the temperature of the h2o will exist displayed in the control console. You should see the temperature steady ascent if the heater is working. In one case the five minutes is up the water pumps out and will automatically exit this test manner. Pressing power anytime during the test style will exit the examination mode.

t08

Hot H2o Valve Test Mode

To enter the hot water valve examination mode on a GE front end load washer, rotate the control knob until t08 is displayed in the command panel then press outset/pause to enter the test mode. This is the hot water valve test style. Once this test style is entered, "hOt" will be displayed in the control console and the hot water will get-go to run. Hot water volition keep to run until the main water level is reached or you press power to exit the test fashion. If the master h2o level is reached before the test mode is terminated, the washer volition pump the water out and return to t08.

Note that some GE front load washer models exercise not accept this exam mode. This can exist a niggling confusing because you can rotate the knob until t08 is displayed; however, when you printing showtime/suspension you hear two beeps and the brandish continues to brandish t08.

t09

Common cold Water Valve Test Mode

To enter the common cold-water exam way on a GE front end load washer, rotate the command knob until t09 is displayed in the control panel then press start/suspension to enter the test fashion. This is the common cold-water valve test manner. In one case this test mode is entered, "Cld" will be displayed in the command panel and the cold h2o will start to run. Cold h2o will go along to run until the main water level is reached or yous printing ability to leave the test manner. If the main h2o level is reached before the exam way is terminated, the washer will pump the water out and return to t09.

Note that some GE front load washer models do not take this exam mode. This can exist a little confusing because you lot tin rotate the knob until t09 is displayed; nevertheless, when you press offset/break you lot hear two beeps and the display continues to display t09.

t10

Tumble Test Mode

To enter the tumble test on a GE front load washer, rotate the control knob until t10 is displayed then printing get-go/suspension to enter the examination mode. Once the test mode is entered, "tt" volition be displayed in the control panel and the spin handbasket volition start to tumble in one direction for five seconds then contrary and tumble for 5 seconds in reverse direction. This will repeat continually until you lot exit the test style by pressing the ability button.

t11

Spin Test Fashion

To enter the spin test on a GE front load washer, rotate the command knob until t11 is displayed then press commencement/pause to enter the exam style. Once the examination mode is entered, the tub will offset to spin and the rpm will be displayed in the command panel. When yous showtime enter the test mode, the spin basket will ramp up to 400 rpm. If you press start/pause a 2nd time the spin basket will ramp up to thousand rpm. Since some displays can only display iii digits you lot may see 999 or 0 in the brandish when the spin basket reaches 1000 rpm.

t12

Dispenser Motor Examination Style

Before I talk about the dispenser motor exam, I will explain the dispenser system. Most GE front load washer models take a dispenser. The dispenser has 4 positions and the dispenser motor switches the dispenser to each position by rotating a h2o diverter in the correct position. On the top of the dispenser there are four numbers that represent each position. Yous should also see the dispenser and an arrow. When the motor rotates, the arrow moves as well every bit the diverter (you tin can't run into the diverter) to the position that it needs to be in according to which cycle the washer is in.

Position 1 corresponds to the pre-wash dispenser function.

Position two corresponds to the wash dispenser function.

Position iii corresponds to the bleach dispenser function.

Position four corresponds to the fabric dispenser function.

This test manner is used to test the dispenser motor.

To enter the dispenser motor exam manner on a GE front load washer, rotate the control knob until t12 is displayed and then printing beginning/pause to enter the exam way. Once the examination mode is entered, the display will display "Pdt" and the dispenser motor will rotate the dispenser until the pointer is pointing to 1 and the washer will start to fill in the pre-wash compartment.

Press start/pause to advance to the next level of the examination. Once done, the dispenser volition plow to the number 2 position, "ddt" will be displayed in the control panel and water will offset to make full in the launder compartment.

Printing outset/pause to advance to the next level of the test mode. Once done, "bdt" will be displayed in the control panel, the dispenser volition turn to the number 3 position and h2o will start to fill in the bleach compartment.

Press commencement/break to advance to the final stage of this test. Once done, "Fdt" will be displayed in the control panel, the dispenser volition plough to the number 4 position and water volition get-go to fill in the fabric softener compartment.

If at anytime during the exam, the main water level is reached, the washer will pump out the water and exit the test mode. Too, if yous press power at anytime it volition leave the test fashion.

Some GE front loader washer models don't have a dispenser motor but even so accept a dispenser test mode. Modes with no dispenser motors have iii water valves, one hot and 2 common cold. The water valves are energized in combinations to make full the right dispenser compartment.

To enter the dispenser test mode on a GE front load washer, rotate the control knob until t12 is displayed then press outset/intermission to enter the test mode. Then "ddt" volition be displayed and the hot water valve volition run to fill the detergent compartment.
Press first/pause to advance and "bdt" volition exist displayed and the #2 common cold water valve will run water into the bleach compartment.

Printing start/pause to accelerate, "Fdt" will be displayed, the #1 common cold water valve and the #2 cold water valve volition run to fill the fabric softener compartment.

Press starting time/pause to advance, "HCt" will be displayed, the #ane common cold h2o valve and the hot water valve will run to fill the detergent compartment.

If at anytime the water reaches the primary water level, the exam will stop.

Press power to exit the test mode and return to t12.

t13

This test has no diagnostic purpose.

t14

Spin Spin Ramp Test Mode

To enter the spin ramp teston a GE front load washer, rotate the control knob until t14 is displayed then press commencement/interruption to enter the test mode. Once the test mode is entered, the spin basket will first to spin and the rpm will be displayed in the command console. First, it will ramp to 100 rpm then to 350 rpm and finally to thousand rpm.

Render From GE Front end Load Washer Service way

Appliance-repair-it.com is a free service but information technology cost to go on information technology up and running. Donate to let this website help you adjacent time! Apparatus parts online, right part, best price and fast shipping.